Call

 

They are making a few great points on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in the article following next.

Setting up a bath tub isn't precisely brain surgery, but it does need solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bath tub with a new one is also a moderately difficult project. If the old tub is easily easily accessible, the task can move easily; if you have to open up a wall surface to eliminate the old tub and position the new tub, the task is much harder. In either case, the task is within a home handyman's skills, although you will require an assistant to move out the old tub and embeded in the brand-new one. See to it you have actually qualified on your own for the work as well as are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed job, it is much better to consider employing one prior to you start. Possibilities are you might need a specialist plumber to make tube links.
This write-up will certainly help you mount a new bath tub in your washroom if you have actually currently gotten a brand-new bathtub and do not need to transform the setup of your previous water supply pipelines.
Your tools and product list should consist of the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Getting ready for the Setup

First of all, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to prevent strain on the tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its final placement.

 

 

Removing Old Touches

If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be fairly bothersome due to the limited accessibility that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Installing the Tub

Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and also adjusting the feet on the tub till the level reads degree.
To install taps, fit all-time low of the outermost versatile faucet connector to the suitable supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and examine all joints and also new pipework for leaks as well as tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and also the regular outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been used at the very least once as this will certainly resolve it right into its last placement.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will certainly need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the producer given backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet ports. The former kind should be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Tub

In the location where the bathroom meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to split a rigid seal, triggering the water to pass through the wall in between the bathroom as well as the tiling, resulting in complications with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the bathtub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof glue as well as cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

We hope you enjoyed reading our article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for taking time to read through our piece. Sharing is good. You just don't know, you may be doing someone a favor. I truly appreciate reading our article about Tools You Need to Install a New Bathtub .

Opt for our expert plumbers.